Package Size: 2 gallon unit (1 gallon part A & 1 gallon part B)
Mixing Ratio: 1 part A to 1 part B
Color: Glossy dark maroon
Optimum Application Temperature: 70 degrees Fahrenheit & above (concrete temperature). If the concrete temperature is going to be less than 70 degrees Fahrenheit, T-184 thinner must be added (up to 10 %). Product should be kept in a warm area of 75 degrees Fahrenheit or above for a minimum of 24 hours prior to application.
Mixing instructions: Mix the 2 gallon unit of Epo-Line 161 in a 5 gallon bucket, then pour that mixture into a second 5
gallon bucket, making sure to crape the sides and bottom of the first bucket to
remove all unmixed material. Mix the contents in the second bucket for a period of 3 minutes minimum. (This will ensure a complete mix of the material
and will not leave soft spots in the completed floor or wall coating.)
Theoretical coverage: 375 sq.ft. per 2 gallon unit at 8 mils per coat. Two coats are required for proper performance and protection. If a non-slip surface is required, non-skid aluminum oxide should be broadcast onto the first coat while it is still wet.
Package Size: 2 gallon unit (1 gallon part A & 1 gallon part B)
Mixing Ratio: 1 part A to 1 part B
Color: Flat gray or off white
Optimum Application Temperature: 70 degrees Fahrenheit & above (concrete temperature). Product should be kept in a warm area of 75 degrees Fahrenheit or above for a minimum of 24 hours prior to application.
Mixing instructions: Mix the 2 gallon unit of Wall-Nu Trowelable in a 5 gallon bucket, then pour that mixture into a second 5
gallon bucket, making sure to crape the sides and bottom of the first bucket to
remove all unmixed material. Mix the contents in the second bucket for a period of 3 minutes minimum. (This will ensure a complete mix of the material
and will not leave soft spots in the completed floor or wall coating.)
(Must be used with Thiocaulk H705)
Package size: 1 quart
Mixing Ratio: No mixing required
Color: Clear
Optimum Application Temperature: 50 degrees Fahrenheit & above (concrete temperature)
Product should be kept in a warm area of 75 degrees Fahrenheit or above for a minimum
of 24 hours prior to application.
Mixing Instructions: Ready to apply - no mixing required.
Theoretical Coverage: 1 quart of #8 Primer will prime the area required for a 2 gallon unit of
Thiocaulk H705.
Package Size: 150 foot roll, 6 inches wide
Package Size: 1 gallon unit
Mixing Ratio: No mixing required - T-100 Thinner is ready to use.
Color: Clear
Optimum Application Temperature: Use when concrete temperature is less than 75 degrees
Fahrenheit.
Mixing Instructions: Mix no more than 10% to Epo-Line 161 to aid in the application onto cold
concrete.
Theoretical Coverage: About the same density as water. Will depend on the application.
(May also be used full strength to clean application tools and equipment.)
Package Size: 1 gallon unit
Mixing Ratio: No mixing required.
Color: Pink or Red
Optimum Application Temperature: Any temperature.
Mixing Instructions: No mixing required. Apply directly to concrete to etch the concrete and
remove any contaminates.
Theoretical coverage: 1 gallon covers approximately 120-150 square feet of concrete.
Package Size: 1 gallon unit
Mixing Ratio: Mix 1 pint of 28% Aqua Ammonia to 5 gallons of water.
Color: Clear
Optimum Application Temperature: Any temperature.
Mixing Instructions: Mix 1 pint of 28% aqua ammonia to 15 gallons of water. Apply to concrete
to neutralize.
Theoretical Coverage: 1 gallon mixed with water covers aproximately 300-400 square feet of
concrete.
Click here to return to EpoSeal Table of Contents